Paxton Access Door Controllers

Icom Security supply and install a wide range of Paxton Access door controllers for many different applications.

Icom Security will provide you with the highest quality Paxton Access door controllers that meet the specific needs and requirements for your access control system.

Below are a range of Paxton Access door controllers from Icom Security.

Paxton Access Control

Paxton Switch2 Door Controllers

Paxton Switch2 Door Controller

Switch2 is a single door control unit. The control unit stores the access permissions of the user and is mounted within the building. This makes the system suitable for high security applications.

Paxton Switch2 can be used with PROXIMITY, CARDLOCK or TOUCHLOCK readers. Switch2 can be installed to many doors over a site, all using the same tokens. Two readers can be connected to a single unit to give read in and read out access control.

Operation of Switch2 Door Controllers

The operation of Switch2 depends on the following modes:

• PROXIMITY and CARDLOCK – User tokens are valid and ready for use once installation is complete. Every user token is supplied with a corresponding shadow card. As user tokens are issued, the name of the user is marked on the shadow card. If a user is to be barred, or a user token is lost, the shadow card marked with the users” name is presented to all readers on site. This simple action invalidates the user token. Another user token may be issued for that user. Additional features can be programmed using the PROXIMITY or CARDLOCK function card pack. These features include zoning which allows you to limit access by token colour.
• TOUCHLOCK – If a valid code is entered access is granted. Codes are changed via the keypad using the master code.
• PROXIMITY KP keypad. Choose card + code, card + PIN, card only or code only.

<Paxton Switch2 Door Controllers Download>

Paxton Net2 Classic Door Controllers

Paxton Net2 Classic Door Controller

Paxton Net2 is a networked access control system. A networked system gives the advantages of central control, event reporting and flexible control over users’ access. Each control unit is part of a network but can run independently making its own decisions and remembering events.

The control unit has FLASH memory which means that firmware can be upgraded from the PC. This is the key to making the system future proof.

Control units are sold as a PCB only, within a plastic housing or mounted within a 2A boxed metal/plastic mains monitored backup power supply.

<Paxton Net2 Classic Door Controllers Download>

Paxton Net2 Nano Door Controllers

The Net2 nano control unit connects to the central administration PC using Paxton Access’ proprietary and secure wireless technology. Net2 nano control units can be mixed with Net2 classic and Net2 plus control units and can be added to existing Net2 installations. This will be particularly useful where wiring would prove difficult.

Control units are sold as a PCB only, within a plastic housing or mounted within a 2A plastic boxed backup power supply. The Net2 nano cannot be mounted in a metal box because of its use of wireless technology.

Paxton Net2 nano should be used with Net2 standard software.

<Paxton Net2 Nano Door Controllers Download>

Paxton Net2 Plus Door Controllers

The Net2 plus control unit connects to the central administration PC using an RJ45 plug into a standard TCP/IP Ethernet network. This greatly increases the flexibility of installation options on sites that have LAN/WAN networks. The Net2 plus control unit also has a RS485 connection. This means it can be connected to other Net2 plus or Net2 classic control units using a dedicated CAT5 cable.

One Net2 plus control unit can be the network interface to the LAN and also run a wired RS485 daisy chain of other Net2 plus or Net2 classic units, removing the need for an independent TCP/IP to RS485 converter.

Control units are sold as a PCB only, within a plastic housing or mounted within a 2A boxed metal/plastic mains monitored backup power supply.

<Paxton Net2 Plus Door Controllers Download>

Paxton Easyprox Nano

Paxton Easyprox Nano

Easyprox nano is an all-in-one battery powered lock reader and access control unit that is ideal for internal doors. Easyprox nano is designed for use with the Net2Air USB bridge or the Net2Air Ethernet bridge to give the advantages of a networked access control system. Networked access control provides event reporting and flexibility over users’access rights. Installing the system is easy because it is not wired into a mains power source.

Easyprox nano connects to the administration PC using Paxton Access’ proprietary and secure wireless technology.

Easyprox nano is perfect for internal doors where wiring would prove difficult.

Easyprox nano should be used with Net2 standard software.

<Paxton Easyprox Nano Download>

Operation of Paxton Net2 Door Controllers

Any changes made at the PC are communicated and stored at the control unit. When a user presents their token to the reader, the control unit identifies them and permits or denies access as appropriate.